Hallo zusammen,
seit kurzer Zeit meldet meine VU Ultimo4k beim Booten aus dem DEEP StandBy folgendes:
Spoiler anzeigen
[ 83.501663] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xe frozen
[ 83.509125] ata1: irq_stat 0x00000040, connection status changed
[ 83.515333] ata1: SError: { PHYRdyChg CommWake DevExch }
[ 83.520729] ata1: hard resetting link
[ 84.068018] ata1: SATA link down (SStatus 0 SControl 300)
[ 84.070024] ata1: EH complete
[ 85.179840] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xe frozen
[ 85.187316] ata1: irq_stat 0x00000040, connection status changed
[ 85.193518] ata1: SError: { PHYRdyChg CommWake DevExch }
[ 85.198894] ata1: hard resetting link
[ 86.058006] ata1: SATA link down (SStatus 0 SControl 300)
[ 86.060004] ata1: EH complete
[ 86.127307] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xe frozen
[ 86.134747] ata1: irq_stat 0x00000040, connection status changed
[ 86.140826] ata1: SError: { PHYRdyChg CommWake DevExch }
[ 86.146197] ata1: limiting SATA link speed to 1.5 Gbps
[ 86.146207] ata1: hard resetting link
[ 87.474019] ata1: SATA link down (SStatus 0 SControl 310)
[ 87.476012] ata1: EH complete
[ 87.900265] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen
[ 87.907725] ata1: irq_stat 0x00000040, connection status changed
[ 87.913926] ata1: SError: { CommWake DevExch }
[ 87.918418] ata1: limiting SATA link speed to 1.5 Gbps
[ 87.918428] ata1: hard resetting link
[ 97.921000] ata1: softreset failed (1st FIS failed)
[ 97.926161] ata1: hard resetting link
[ 107.928994] ata1: softreset failed (1st FIS failed)
[ 107.933905] ata1: hard resetting link
...
[ 228.417001] ata1: softreset failed (1st FIS failed)
[ 228.421908] ata1: hard resetting link
[ 231.270004] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 231.272640] ata1.00: ATA-10: ST8000VN0022-2EL112, SC61, max UDMA/133
[ 231.272662] ata1.00: 15628053168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 231.275123] ata1.00: configured for UDMA/133
[ 231.275139] ata1: EH complete
[ 231.275355] scsi 0:0:0:0: Direct-Access ATA ST8000VN0022-2EL SC61 PQ: 0 ANSI: 5
[ 231.276373] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 231.276676] sd 0:0:0:0: [sda] 15628053168 512-byte logical blocks: (8.00 TB/7.27 TiB)
[ 231.276683] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 231.277178] sd 0:0:0:0: [sda] Write Protect is off
[ 231.277188] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 231.277259] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 231.295942] sda: unknown partition table
[ 231.296754] sd 0:0:0:0: [sda] Attached SCSI disk
Die Platte wird so auch nicht automatisch gemountet und meine "Aufnahmen" landen im internen Speicher der VU
Nach einem Reboot funktioniert die Platte dann normalerweise wieder problemlos.
Mir kommt es so vor, als wenn die Platte beim Booten nicht immer richtig anläuft
Nach
Hat jemand vielleicht Erfahrung ob vermutlich
1) die Platte
2) Das Kabel
Mir kommt es so vor, als wenn die Platte nicht immer richtig anläuft
3) das Netzteil
4) das VU Board
eine Macke hat?
Wäre dankbar für Tipps.
p-body
seit kurzer Zeit meldet meine VU Ultimo4k beim Booten aus dem DEEP StandBy folgendes:
[ 83.501663] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xe frozen
[ 83.509125] ata1: irq_stat 0x00000040, connection status changed
[ 83.515333] ata1: SError: { PHYRdyChg CommWake DevExch }
[ 83.520729] ata1: hard resetting link
[ 84.068018] ata1: SATA link down (SStatus 0 SControl 300)
[ 84.070024] ata1: EH complete
[ 85.179840] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xe frozen
[ 85.187316] ata1: irq_stat 0x00000040, connection status changed
[ 85.193518] ata1: SError: { PHYRdyChg CommWake DevExch }
[ 85.198894] ata1: hard resetting link
[ 86.058006] ata1: SATA link down (SStatus 0 SControl 300)
[ 86.060004] ata1: EH complete
[ 86.127307] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xe frozen
[ 86.134747] ata1: irq_stat 0x00000040, connection status changed
[ 86.140826] ata1: SError: { PHYRdyChg CommWake DevExch }
[ 86.146197] ata1: limiting SATA link speed to 1.5 Gbps
[ 86.146207] ata1: hard resetting link
[ 87.474019] ata1: SATA link down (SStatus 0 SControl 310)
[ 87.476012] ata1: EH complete
[ 87.900265] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen
[ 87.907725] ata1: irq_stat 0x00000040, connection status changed
[ 87.913926] ata1: SError: { CommWake DevExch }
[ 87.918418] ata1: limiting SATA link speed to 1.5 Gbps
[ 87.918428] ata1: hard resetting link
[ 97.921000] ata1: softreset failed (1st FIS failed)
[ 97.926161] ata1: hard resetting link
[ 107.928994] ata1: softreset failed (1st FIS failed)
[ 107.933905] ata1: hard resetting link
...
[ 228.417001] ata1: softreset failed (1st FIS failed)
[ 228.421908] ata1: hard resetting link
[ 231.270004] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 231.272640] ata1.00: ATA-10: ST8000VN0022-2EL112, SC61, max UDMA/133
[ 231.272662] ata1.00: 15628053168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 231.275123] ata1.00: configured for UDMA/133
[ 231.275139] ata1: EH complete
[ 231.275355] scsi 0:0:0:0: Direct-Access ATA ST8000VN0022-2EL SC61 PQ: 0 ANSI: 5
[ 231.276373] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 231.276676] sd 0:0:0:0: [sda] 15628053168 512-byte logical blocks: (8.00 TB/7.27 TiB)
[ 231.276683] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 231.277178] sd 0:0:0:0: [sda] Write Protect is off
[ 231.277188] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 231.277259] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 231.295942] sda: unknown partition table
[ 231.296754] sd 0:0:0:0: [sda] Attached SCSI disk
Die Platte wird so auch nicht automatisch gemountet und meine "Aufnahmen" landen im internen Speicher der VU
Nach einem Reboot funktioniert die Platte dann normalerweise wieder problemlos.
Mir kommt es so vor, als wenn die Platte beim Booten nicht immer richtig anläuft
Nach
smartctl -a /dev/sda/
ist die Platte allerdings unauffällig.Hat jemand vielleicht Erfahrung ob vermutlich
1) die Platte
2) Das Kabel
Mir kommt es so vor, als wenn die Platte nicht immer richtig anläuft
3) das Netzteil
4) das VU Board
eine Macke hat?
Wäre dankbar für Tipps.
p-body
VU + Ultimo4K, VU+ Duo4K, VU + Zero4K:
VTi 15.0.02 (2022-12-15-vti-master (99a40fe7d))
VTi 15.0.02 (2022-12-15-vti-master (99a40fe7d))