externer Kartenleser

Es will nicht ich geb,s auf

auf Normal eingestellt habe ich ,mit den Notepad ++ noch nichts

Der Cocksy hat doch auch so ein smargo vieleicht weiss er an was es liegt

SERIAL Reader :/dev/usb/tts/0 Smartreader+ ":x" x

# But if smartcard has hidden/unknown chids, all chids should be tried.
# In that case specify 'TRY ALL CHIDS' option for cardreader.
# Use with care, enabling option causes more card traffic.
# Only use setting when some channels don't work without it.
# note: if even this setting don't help decode all channels, try using
# commandline arg -l, to disable all self-learning features (warning: slower)

#TRY ALL CHIDS : <device>
#
#example: card in /dev/ttyUSB0 gets ecm for all possible chids, not
#just the chids it officially supports
#
#TRY ALL CHIDS : /dev/ttyUSB0

# perform smartcard post init commands
#
# POSTINIT : <device> <filename> (<autodelete>)
#
# send commands in 'filename' to 'device', and delete 'filename' when
# optional 'autodelete' argument nonzero
#
#example:
#
#POSTINIT : /dev/sci0 /tmp/postinit
#
#example /tmp/postinit contents:
#c134000003000000
#c13201000a

# Option to override autodetected dvb api version. Restart needed.
#
#DVB API: <value>
#
# <value> -1 = no dvb, 1 = dvb api 1, 3 = dvb api 3
#
# WARNING: only use when autodetect fails!
#
#example, disable nonworking dvb hardware:
#DVB API: -1

# Option to set global share limits
#
#GLOBAL LIMITS: { caid:id(:downhops), caid:id(:downhops), ... }
#
#example:
#
#GLOBAL LIMITS : { 0100:000080, 0622:000000:1, 0500:000000:2 }
#
# all users get no 0100:000080.
# and our 0622:000000 cards only for themself (1 hop down),
# and 0500 cards for themself plus one additional hop down.
# global limits are overridden by client specific limits (see F:)

# Option to reject shares with less than required downhops on clientside
#
#MINIMUM DOWNHOPS: <value>
#
# default: 0 (don't ignore any shares)
#
#example:
#
#MINIMUM DOWNHOPS: 1
#
# ignore shares that have less than 1 'downhops' (i.e. can not be shared
# further down to other clients)

# Option to ignore all shares that go through a certain node
#
#IGNORE NODE: <nodeid>
#
#example, ignore two nodes:
#
#IGNORE NODE: ccd536ab515767ad
#IGNORE NODE: aad536ab515761af


# The seca handler is used to better support simulcrypt on the same ident
#
# With this setting you can change the behaviour of how SECA has to be used
# This setting is ignored unless SECA2/SECA3 simulcrypt is detected!!
#
# When disabled CCcam behaves like previous versions
#
# When "prefer SECA3 over SECA2" is enabled try to use SECA3 ecm first, then SECA2
#
# When "Ignore SECA2" is enabled, ignore all SECA2 ecm so a SECA3 card will not get SECA2 request which it cannot handle
#
# When "Ignore SECA3" is enabled, ignore all SECA3 ecm so a SECA2 card will not get SECA3 request which it cannot handle
#
#
# The following settings can be used
#
# SECA HANDLER: <value>
# <value> : 0 = disabled, 1 = prefer SECA3 over SECA2, 2 = prefer SECA2 over SECA3, 3 = Ignore SECA2, 4 = Ignore SECA3
#
# default: 1
#
# Example try to use SECA3 ecm first, then SECA2
#SECA HANDLER: 1
#
# Example try to use SECA2 ecm first, then SECA3
#SECA HANDLER: 2
#
# Example to ignore all SECA2 ecm so a SECA3 card will not get SECA2 request which it cannot handle
#SECA HANDLER: 3
#
# Example to ignore all SECA3 ecm so a SECA2 card will not get SECA3 request which it cannot handle
#SECA HANDLER: 4


# Configure limited list of accepted sids for smartcard
# When omitted, all sids are allowed.
# (can work together with LOADBALANCE configuration, or for standalone cards)
#
# SMARTCARD SID ASSIGN : <device> <maxnumberofsids> { <sid1>, <sid2>, ... <sidn> }
#
# <device> is the reader devicenode
# <maxnumberofsids> limits the total number of sids assigned to the card (0 = use length of sid list)
# { <sid1>..<sidn> } lists the sids that are assigned to the smartcard, when omitted, <maxnumberofsids> is used to auto assign sids
#
# when <maxnumberofsids> is larger than the length of the sidlist, the remainder of the sids are auto assigned, till the list reaches <maxnumberofsids>
# Check entitlement output for realtime assignment list
#
# WARNING: when SMARTCARD SID ASSIGN config changes, restart is required before settings take effect
#
#example1: smartcard in device /dev/ttyUSB0 only handles requests for sids df3, df4, df5
#
# SMARTCARD SID ASSIGN : /dev/ttyUSB0 0 { 0df3,0df4,0df5 }
#
#example2: smartcard in device /dev/ttyUSB0 handles requests for max 5 sids, auto assigned in the order of occurance. A request for a 6th sid will be denied.
#
# SMARTCARD SID ASSIGN : /dev/ttyUSB0 5
#
#example3: smartcard in device /dev/ttyUSB0 handles requests for max 5 sids, 3 of which are df3, df4, df5, remaining 2 are auto assigned
#
# SMARTCARD SID ASSIGN : /dev/ttyUSB0 5 { 0df3,0df4,0df5 }

Das steht ider beschreibung punkt 10

Habe ich gemacht

nichts

root@bm750:~# dmesgroot@bm750:~# dmesg
-sh: dmesgroot@bm750:~#: not found
root@bm750:~#
root@bm750:~#
root@bm750:~#
root@bm750:~#


meinst du das

was soll ich wo eingeben

jetzt krieg ichs nicht mehr kopiert.

ich komm nicht mehr weiter