Suchergebnisse

Zitat: „Original von grtmoby u have to rename the file on the hard disk from epg_new.dat to epg.dat and restart gui“ Thanks grtmoby Already tried that and when I reboot, the file in media/hdd dissappears. I have also just installed coolepg v2.8 in extensions its in there but I can't get this to activate either. I hope the epg is in the plugins on the next vti release so it can be installed auto. I have been trying to get an epg working now for the last three days and still haven't managed it. Ho…

Zitat: „Originally posted by stauffie Zitat: „Originally posted by stauffie if you can not get in under control try to flash vti image and tell us if freezers are still there on Free To Air Channels“ that is realy going to make me curious if the error still exist with the VTi“ no problems now running fine on vti Regards jcl

Hi Guys I have managed to install rytec in vti v2.0 It's sitting there in my plugins (EPGimport automated epg importer) When I open epg I have set the config to auto enable 8pm. Then blue button (sources) select Rytec UK XMLTV Then green button Then yellow button epg then imports the events for rytec uk after this I reboot, then when I open my channel lists the epg is not there. where am I going wrong Thanks Regards jcl

thanks satmanbasil this is a new vu+ my son has purchased so in the morning I'm going to check it out. I am going to install vti and see if this problem persists. I will let you know the outcome. regards jcl

Zitat: „Originally posted by xener Zitat: „Originally posted by tonskidutch wait... FTA is clear, yet when you have a softcam installed and activated it also interferes with FTA reception getting and or sending requests i thought that knowledge would be elementary ciao“ really? how softcam interfering with FTA reception, please?“ I wish I knew regards jcl

Thanks for the replies guys the softcam I am using is Cccam Oscam 2.1.3 image VIX the only plugins installed are cccam and autoresolution. connected to the internet freezing picture disconnected from the internet stable picture all sd and hd fta channels tried reinstalling image loaded channel list (catseye latest) and no plugins so no cams or configs or autoresolution installed and I've still got the same problem. also I have tried both my internet connections which are vermin and talktalk with…

Thanks for the reply yes the signal quality was the first thing I checked. plugins autoresolution and cccam the signal is the same whether it is connected to the internet or not. there is no freezing on any sd or hd channels when disconnected from the internet. problem only occurs when connected to internet. Regards jcl

Hi Guys Vu+ duo when viewing any fta HD channels the picture freezes a lot. If I disconnect the internet connection from the box the freezing stops. Any ideas what would be causing this to freezing when connected to the internet Thanks Regards jcl

factory reset reinstalled rytec still not working regards jcl

Thanks Cytrax yes I used this file to install rytec must have gone wrong somewhere. I will reinstall and post when I've done it regards jcl

Hi Guys trying to install rytec in vti latest image when I open plugins under blue button I get this error message. some plugins are not available extension/EPGImport(module object has no attributes epgimport) where am I going wrong thanks regards jcl

Glad you got it sorted mate Regards jcl

check that the switch at the back of the box is turned on. change the fuse in the plug it might have blown regards jcl

Hi Guys How do i fine tune my motorised dish in the vti menu my dish is set up for usals and works fine on most satellites but snr on sirius is a little low at 40%/agc73% Thanks Regards jcl

and i keep getting the same error Regards jcl

Thanks for the reply realmagic. just found out you don't have to press the red button as the remote works similar to the db7000 remote. If you want a channel say beginning with B press number 2 button 3 times. first press data channels beginning with number 2 second press channels beginning with A Third press channels beginning with B Regards jcl

hi guys the vu+ remote control as you have probably noticed is numbered 1 to 0 numbers 2 to 9 also have the letters of the english alphabet. I also have a dreambox 7000 and the remote is set out the same with letters on numbers 2 to 9. On my dreambox when i press the up or down arrow the channel list appears on screen and then if i press say as an example the number 7 once all channels beginning with P will appear on the screen if i press the same number 7 four times all channels beginning S wil…